Astm a105 is a standard specification of round bars. Astm a105 round bars are used in variety of industrial operations because of their strong Composure, easy application, reliability and availability of different types. These round bars are made up of 0.30% to 0.60% of carbon, and other elements like Manganese, phosphorus, sulphur and iron are also present which makes its structure very Strong. It also displays high tolerance, good corrosion resistance, longevity, ductility and good Weldability. Different types of astm a105 round bar like hot rolled, cold drawn and polished bars are Also available as their uses may vary with different demands. Aashish steel is a trusted and prominent manufacturer of these bars. They also provide Variety of bars like stainless steel, seamless and duplex round bars to meet the expectation And requirements of the customers. They are well known for exporting high quality, cold drawn bars which have high tensile Strength.
When using carbon steel A105 bars, one should be aware of the tolerance level of the bars as it is really important for the overall structure. More tolerance is directly equal to high strength and good longevity. H Tolerance (H9, H11) H tolerances are hole limits in engineering and machining. The"H"; would be the definition that the tolerance is based on the hole rather than the shaft. H9 The tolerance is closer with tighter limits, but normally generates a medium fit for most of the applications where precision matters. H11 This tolerance is a little slack compared with H9 and allows the shaft to accommodate some play. It is normally used wherever some clearance will be acceptable. K Tolerance (K12, K13): Definition: The use of K tolerances is for shafts and shows the limits on their sizes. K12 A closer fit with specified diametric limits, which gives a precise fit K13 Slightly similar to K12 but with a little more looseness to allow some clearance in the assembly. Straightness is the amount that a line departs from being straight across its length. It is, in fact one of the important geometrical tolerances in engineering and manufacturing.

Table of Content
A105 and SA 105 are different kinds of material standard used in industrial sectors where there are specific demands related to the operating conditions. Both of these round bars showcase high strength, durability, longevity and tolerance. They are available in different kinds of surface finishes like hot rolled, cold drawn, etc and hardness like Brinell Hardness as per the requirements of the customers. Few are explained below: Hot rolled is the steel at high temperature to achieve desired shape. Gives a rough surface. Cold drawn achieved by putting the steel into a die and pulling to achieve required size and shape. This is done at room temperature. Brinell hardnes: has a range of 120 to 170 HB that may vary as per production differences.
ASTM A105 Round Bar Manufacturer in India, Available in Different Sizes to Suit Customer Requirements. It is Used inVarious Fittings,Piping ComponentsValves,Forging Flanges.
ASTM A105 Round Bar Specification
A105 Steel Rod Sizes
A105 Carbon Steel Round Bar Other Products Sizes
A105 Forged Steel Bars Length & Tolerance
Manufacturing Techniques of A105N Carbon Steel Rounds
ASTM A105 Flat Bar Surface Finish
A105 Steel Rod Processing Services
ASTM A105 Steel Rectangular Bar Application
CS ASTM A105 hex bar Cutting Methods
A105 Normalized Square Bar Documentation
Testing Methods of Low Temp Carbon Steel Bright Bar
SA 105 Hexagonal Bar Value Added Services

A105 Galvanized Bar Test Certificates
UNS K03504 is a standard specification for material that are made from low carbon steel. It has a carbon content of 0.04% to 0.06% and is very ductile because of that. It shows good strength and tolerance in less demanding conditions or low pressure zones hence it is very useful in low scale industries. Industries involved in manufacturing, automotive and construction make use of this material because of its good weldability, ductile nature, good strength and machinability. The weight chart of Carbon UNS K03504 Round Bars is a very important part as it contains valuable information like size, dimensions and weight of the material. Following the weight chart for better understanding:
Types of ASTM A105 Carbon Steel Rod
ASTM A105 Carbon Steel Rolled Flat Bar
SA 105 Carbon Steel Sheared & Edged Bar
ASME SA Carbon Steel Half Round Bar
A105n Carbon Steel Round Bar
ASTM A105n Carbon Steel Hex Bar
A105n Forged Carbon Steel Square Bar
CS ASTM A105 Carbon Steel Bright Bar
A105 Carbon Steel Flat Bar
SA 105 Carbon Steel Threaded Bar
ASTM A105 Carbon Steel Bearing Quality Bar
A105n Normalized Carbon Steel Accuracy Bar
ASTM A105 UNS K03504 Carbon Steel Pump Shaft Quality Bar
SA 105 Carbon Steel Black Bar
ASME SA 105 High Carbon Steel Rod
A105 Carbon Steel Triangle Bar
Aashish Steel is the most progressive and cost-effective manufacturing sector. ASTM A105 Round Bar Supplier in India, Produce a Wide Range of Carbon Steel Round Bar in Various Sizes and Grades.
AISI EN 10060, UNS, DIN and ASTM are international standard which are given to the material if it meets the required standard. Several tests are carried out to test the quality and authenticity of the material and only then, the manufacturer receives a certification to manufacture and supply these bars. This certification gives assurance to the customers that the product is of standard quality and Aashish steel is one of the top exporters of SA105 Steel Bar & JIS A105 Bars which are made as per the international standards. They also export materials with equivalent standards to help engineers that are working with different material and for this, a weight chart can be very helpful as it has information related to the standard and weight of the material.
Weight Chart of ASTM A105 Carbon Steel Round Bars Per Linear Foot
| SIZE IN INCHES | ROUND | SQUARE | OCTAGON | HEXAGON | SIZE IN INCHES | ROUND | SQUARE | OCTAGON | HEXAGON |
|---|---|---|---|---|---|---|---|---|---|
| 1/16 | .010 | .013 | .011 | .012 | 11/16 | 1.262 | 1.607 | 1.333 | 1.392 |
| 5/64 | .017 | .022 | .018 | .019 | 45/64 | 1.320 | 1.681 | 1.394 | 1.456 |
| 3/32 | .023 | .029 | .024 | .025 | 23/32 | 1.380 | 1.756 | 1.487 | 1.521 |
| 7/64 | .031 | .039 | .033 | .034 | 47/64 | 1.440 | 1.834 | 1.521 | 1.588 |
| 1/8 | .042 | .053 | .044 | .046 | 3/4 | 1.502 | 1.913 | 1.586 | 1.656 |
| 9/64 | .053 | .067 | .056 | .058 | 25/32 | 1.630 | 2.075 | 1.721 | 1.797 |
| 5/32 | .065 | .083 | .069 | .072 | 13/16 | 1.763 | 2.245 | 1.862 | 1.944 |
| 11/64 | .079 | .100 | .083 | .087 | 27/32 | 1.901 | 2.421 | 2.008 | 2.096 |
| 3/16 | .094 | .120 | .099 | .104 | 7/8 | 2.045 | 2.603 | 2.159 | 2.254 |
| 13/64 | .110 | .140 | .116 | .121 | 29/32 | 2.193 | 2.792 | 2.316 | 2.418 |
| 7/32 | .128 | .163 | .135 | .141 | 15/16 | 2.347 | 2.988 | 2.479 | 2.588 |
| 15/64 | .147 | .187 | .155 | .162 | 31/32 | 2.506 | 3.191 | 2.646 | 2.763 |
| 1/4 | .167 | .213 | .176 | .184 | 1 | 2.670 | 3.400 | 2.820 | 2.945 |
| 17/64 | .188 | .240 | .199 | .207 | 1-1/16 | 3.015 | 3.838 | 3.183 | 3.324 |
| 9/32 | .211 | .269 | .223 | .233 | 1-1/8 | 3.380 | 4.303 | 3.569 | 3.727 |
| 19/64 | .235 | .300 | .248 | .259 | 1-3/16 | 3.766 | 4.795 | 3.977 | 4.152 |
| 5/16 | .261 | .332 | .275 | .288 | 1-1/4 | 4.172 | 5.313 | 4.407 | 4.601 |
| 21/64 | .288 | .360 | .304 | .318 | 1-5/16 | 4.600 | 5.857 | 4.858 | 5.072 |
| 11/32 | .316 | .402 | .334 | .348 | 1-3/8 | 5.049 | 6.428 | 5.332 | 5.567 |
| 23/64 | .345 | .439 | .364 | .381 | 1-7/16 | 5.518 | 7.026 | 5.827 | 6.085 |
| 3/8 | .376 | .478 | .397 | .414 | 1-1/2 | 6.008 | 7.650 | 6.345 | 6.625 |
| 25/64 | .408 | .519 | .431 | .450 | 1-9/16 | 6.519 | 8.301 | 6.885 | 7.189 |
| 13/32 | .441 | .561 | .466 | .486 | 1-5/8 | 7.051 | 8.978 | 7.446 | 7.775 |
| 27/64 | .475 | .605 | .502 | .524 | 1-11/16 | 7.604 | 9.682 | 8.030 | 8.385 |
| 7/16 | .511 | .651 | .540 | .564 | 1-3/4 | 8.178 | 10.41 | 8.634 | 9.018 |
| 29/64 | .548 | .698 | .579 | .604 | 1-13/16 | 8.773 | 11.17 | 9.265 | 9.673 |
| 15/32 | .587 | .747 | .620 | .647 | 1-7/8 | 9.388 | 11.95 | 9.911 | 10.35 |
| 31/64 | .627 | .798 | .662 | .692 | 1-15/16 | 10.02 | 12.76 | 10.58 | 11.05 |
| 1/2 | .668 | .850 | .705 | .736 | 2 | 10.68 | 13.60 | 11.28 | 11.78 |
| 33/64 | .710 | .904 | .750 | .783 | 2-1/16 | 11.36 | 14.46 | 11.99 | 12.53 |
| 17/32 | .754 | .960 | .796 | .831 | 2-1/8 | 12.06 | 15.35 | 12.73 | 13.30 |
| 35/64 | .799 | 1.017 | .844 | .881 | 2-3/16 | 12.78 | 16.27 | 13.49 | 14.09 |
| 9/16 | .845 | 1.076 | .892 | .932 | 2-1/4 | 13.52 | 17.21 | 14.27 | 14.91 |
| 37/64 | .893 | 1.136 | .943 | .985 | 2-5/16 | 14.28 | 18.18 | 15.08 | 15.75 |
| 19/32 | .941 | 1.199 | .994 | 1.038 | 2-3/8 | 15.06 | 19.18 | 15.91 | 16.61 |
| 39/64 | .992 | 1.263 | 1.048 | 1.094 | 2-7/16 | 15.87 | 20.20 | 16.75 | 17.49 |
| 5/8 | 1.043 | 1.328 | 1.102 | 1.150 | 2-1/2 | 16.69 | 21.25 | 17.62 | 18.40 |
| 41/64 | 1.096 | 1.395 | 1.207 | 1.209 | 2-9/16 | 17.53 | 22.33 | 18.52 | 19.34 |
| 21/32 | 1.150 | 1.464 | 1.214 | 1.268 | 2-5/8 | 18.40 | 23.43 | 19.43 | 20.29 |
| 43/64 | 1.205 | 1.535 | 1.272 | 1.329 | 2-11/16 | 19.29 | 24.56 | 20.37 | 21.27 |
Importer and Exporter of A105 Steel Rod Provides Excellent Quality and Prominent Delivery Service. Distribute in a Range of Countries, Including Turkey, Malaysia, Lebanon, Dubai, Oman, and Qatar etc.
Equivalent Chart of A105n Carbon Steel Round Bars Per Linear Foot
| Standard | A105 |
|---|---|
| UNS | K03504 |
| WERKSTOFF NR. | 1.0460 |
| AFNOR | - |
| JIS | - |
| GOST | - |
| BS | - |
| EN | - |
A105n Round Bar & CS A105 Square Bar are equivalent standard materials which share same properties in almost all aspects like yield strength, hardness, tensile strength, etc. Inconel X-750 and Inconel 801 possess impressive mechanical properties: a minimum yield strength of 205 MPa, tensile strength between 480 and 620 MPa, and approximately 20% elongation in 50 mm, indicating good ductility. Their hardness ranges from 137 to 187 HB, enhancing durability and wear resistance. These characteristics make them reliable for demanding applications. These bars are wanted by wide number of industrialists due to high tensile strength, hardness and ductile properties. Aashish steel is a well renowned and prominent stockist of these Bar in Mumbai to cater to the urgent needs of the customers as even a small delay can lead to a big loss.
SA 105 Forged Steel Bar Mechanical Properties
| Tensile strength (psi) min | 70,000 psi |
| Yield strength (psi) min | 36,000 psi |
| Reduction of area (%) min | 30% |
| Elongation in 2” (%) min | 22% |
| Brinell Hardness (BHN) max | 187 |
High Carbon Steel Round Bar Chemical Composition
| Carbon Steel | C | Si | S | Cr | Mn | P |
| A105 | 0.35 | 0.10-0.35 | 0.040 | 0.30 | 0.60-1.05 | 0.035 |
Physical Properties of A105n Normalized Bars
| Density (Lb/in 3) | 0.292 |
| Density (G/cm 3) | 8.08 |
| Density (G/cm 3) | 2600 |
| Melting Point (°c) | 1425 |
SAE 1018 Round Bars Machinability
| Property | Details |
|---|---|
| Material Composition | Carbon, manganese, phosphorus, sulfur, silicon |
| Machinability Rating | 60-65% compared to free-cutting steel (100%) |
| Cutting Tools | High-speed steel (HSS) or carbide tools |
| Cutting Speeds | Medium range (depends on tool and operation) |
| Coolants | Recommended to enhance tool life and surface finish |
| Heat Treatment | Normalized or annealed conditions are preferable |
| Common Applications | Pressure-containing fittings and flanges |
A105 Hot Rolled Round Bar Destructive and Non-Destructive Testing
| Testing Method | Advantages |
|---|---|
| Radiographic Test | Non-destructive; reveals hidden defects. |
| PMI | Ensures compliance; prevents mix-ups. |
| Chemical Examination | Verifies material properties. |
| Buckling & Crushing Test | Assesses structural integrity. |
| Pitting Corrosion Test | Identifies potential issues early. |
| Mechanical Examination | Provides insights into material performance. |
| Eddy Current Test | Fast and effective for surface flaws. |
What are the key features of ASME SA105 Square Bar ?
| Feature | Description |
|---|---|
| Material Composition | Carbon steel (C, Mn, P, S, Si) |
| Mechanical Properties | Good tensile and yield strength; ductile |
| Standard Specification | Conforms to ASME SA105 |
| Heat Treatment | Typically normalized or annealed |
| Machinability | Generally good machinability |
| Weldability | Suitable for welding |
| Applications | Used in pressure vessels and piping systems |
| Dimensions | Available in various sizes |
| Corrosion Resistance | May be treated for enhanced resistance |
| Testing and Certification | Subjected to mechanical and chemical tests |
Are Carbon Steel A105 Bars Suitable for Welding?
Yes, ASTM A105 round bars are generally suitable for welding. This specification covers carbon steel forged fittings, flanges, and valves for use in pressure systems.
| Features | Details |
|---|---|
| Material | ASTM A105 Round Bars |
| Weldability | Generally suitable for welding |
| Common Uses | Pressure systems, fittings, flanges, valves |
| Welding Procedures | Follow proper welding techniques |
| Preheating | May be recommended based on thickness |
| Post-Weld Treatment | Possible need for heat treatment |
| Consultation | Refer to relevant codes and standards |
Can ASTM A105 round bars be heat-treated?
| Property | Details |
|---|---|
| Heat Treatment | Yes |
| Common Processes | Normalizing, Annealing, Quenching/Tempering |
| Purpose | Achieve desired mechanical properties |
| Guidelines | Consult specifications for best practices |
Delivery Time Table of SA 105 Steel Bar
| Sr No | Country | Country Name | Delivery Time |
|---|---|---|---|
| 1 | Egypt | 18 days | |
| 2 | UAE | 5 days | |
| 3 | Jordan | 21 days | |
| 4 | Singapore | 8 days | |
| 5 | Thailand | 7 days | |
| 6 | South Africa | 25-30 days | |
| 7 | Saudi Arabia | 7 days |
Copyright © 2024 Aashish Steel | All rights reserved. Design & SEO By MESOTEK